Red-Gsm - Forum o Mobitelima


Go Back   Red-Gsm - Forum o Mobitelima > Operativni Sustavi / Software / Aplikacije > Ostali operativni sustavi > Windows Mobile


Odgovori
 
Bookmark and Share Alati Za temu
Staro 08-12-2010   #1
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno [HP iPAQ 914c] upgrade ROM-a

Srušio mi se ROM, pokušao sam flešati sa SD karticom, i to s četiri različite kartice međutim uvijek isto javlja "Update error! PLS check!". Nakon toga sam pokušao upgrade s HP-om (sp43444),međutim kad pokrenem isti pokušava se spojiti preko ActiveSync-a, ali neuspješno. Što radit?
viki je odsutan trenutno   Reply With Quote
Staro 08-12-2010   #2
dxdy
Super Moderator
 
dxdy's Avatar
 
Dob: 47
Mobitel: Xiaomi Poco X3 NFC
Operater: ViP
Postovi: 7,634
Zahvalio: 428
Pohvaljen 6,964 Puta u 2,902 Posta
Uobičajeno

evo sa sluzbenih HP stranica postupak flashiranja

i koliko vidim, sluzbeni ROM je sp43434 a ne sp43444

Download

Quote:
HOW TO USE:

1. Download the sp43434.exe to a directory on your hard drive.

2. Execute the downloaded file and follow the on-screen instructions to unpack the ROM update files to a directory.

NOTE: This directory should not contain any file or folder from any previous ROM upgrade.

3. Establish an ActiveSync connection between the iPAQ device and the host PC using a USB connection.

4. The ROM Update Utility (hpRUU.exe) starts automatically. Follow the on-screen instructions to complete the ROM upgrade.

NOTE: Once the update is complete, the .EXE file downloaded in Step 1 can be deleted, if desired.

INSTALLATION NOTES:

1. IMPORTANT: Disable the Standby and Hibernation modes on the host PC. If Standby or Hibernation mode is activated during the upgrade process, a critical error may occur.

2. IMPORTANT: Plan enough time to complete the update. The total time to perform this ROM update is estimated at 40 minutes.

3. IMPORTANT: Do not interact with the HP iPAQ device or remove it from AC power or the cradle/cable once the status bar appears on the iPAQ device and the actual update has started.

4. During the update, the ROM Update Utility:
- Queries the iPAQ device for current ROM image information.
- Validates that the new ROM image is compatible with the iPAQ device.
- Automatically places the iPAQ device in Flash mode.
- Updates the ROM image on the iPAQ device.

5. If an error message is displayed during the update process, follow any available instructions to correct the condition and start the ROM Update Utility again.

6. IMPORTANT: The update process can be performed while connected to a Host PC/Notebook either as a guest or with an established partnership. In case of the Vista Operating System, it is recommended to perform a ROM update as an Administrator.

7. IMPORTANT: For a seamless experience, we recommend the SIM card to be removed from the device before starting the update process.
dxdy je odsutan trenutno   Reply With Quote
Zahvalili:
viki (08-12-2010)
Staro 08-12-2010   #3
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno

Probao sam to međutim, program se pokrene na PC-u Bootloader,koji dođe do 50% i onda stane, na mobilteu piše RUU, "writting eboot". Nakon nekog vremena izbaci grešku "401",koja kaže da je nemoguće uspostaviti vezu između PC-a i devicea. U međuvemenu nakon pokretanja actve sync se pokušava spojiti.
Hvala, dxdy!
viki je odsutan trenutno   Reply With Quote
Staro 08-12-2010   #4
dxdy
Super Moderator
 
dxdy's Avatar
 
Dob: 47
Mobitel: Xiaomi Poco X3 NFC
Operater: ViP
Postovi: 7,634
Zahvalio: 428
Pohvaljen 6,964 Puta u 2,902 Posta
Uobičajeno

jesi isklucio standby (i screensaver) te hibernaciju na kompu?

koji OS imas?
dxdy je odsutan trenutno   Reply With Quote
Zahvalili:
viki (08-12-2010)
Staro 08-12-2010   #5
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno

OS-v1.01.01
FW-v1.09

Dakle mogu upaliti mobitel, te mi pokaže HP invent i gore navedeno, ali ne pokreće mi windowse, kao da ih nema. Probao sam i hard reset, u gornjem dijelu ekrana piše "clean boot" i dalje ne ide. Kad pokušam flešati preko SD kartice, javlja mi "Update error! Pls check!".
Što učiniti???
viki je odsutan trenutno   Reply With Quote
Staro 08-12-2010   #6
dxdy
Super Moderator
 
dxdy's Avatar
 
Dob: 47
Mobitel: Xiaomi Poco X3 NFC
Operater: ViP
Postovi: 7,634
Zahvalio: 428
Pohvaljen 6,964 Puta u 2,902 Posta
Uobičajeno

a da nisi zeznio boot sa ovom verzijom sp43444?

OS sam misio koji imas na kompjteru.. XP ili vista
dxdy je odsutan trenutno   Reply With Quote
Zahvalili:
viki (09-12-2010)
Staro 09-12-2010   #7
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno

Na PC-u mi je XP, ali radio sam boot sa verzijom koju si mi ti napisao sp43434,ali nemože uspostaviti konekciju. Ali mi je čudno kada sam htio i flešati novi ROM sa četiri različite SD kartice, svaki puta mi pokaže istu grešku "Update error!Pls check!".
viki je odsutan trenutno   Reply With Quote
Staro 11-12-2010   #8
dxdy
Super Moderator
 
dxdy's Avatar
 
Dob: 47
Mobitel: Xiaomi Poco X3 NFC
Operater: ViP
Postovi: 7,634
Zahvalio: 428
Pohvaljen 6,964 Puta u 2,902 Posta
Uobičajeno

ne znam sto da ti vise kazem... sve sto znam i sto sam radio sa drugim uredjajima (iPAQ-ima) to sam ti rekao... sa tim modelom nisam radio

jedino sto mogu probat savjetovat je da probas na drugom kompu, drugim kablom
dxdy je odsutan trenutno   Reply With Quote
Staro 20-12-2010   #9
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno

Dxdy,

da li mi možeš pomoći oko ovoga. Nije mi jasan dio oko hex editora, ako imaš kakvih saznanja pomagaj, jer mi telefon treba :


Editing the downloaded file from HP site.
- Download the file from the HP site. The link I used was:
http://h20000.www2.hp.com/bizsupport...scription.jsp?
lang=en&cc=us&prodTypeId=215348&prodSeriesId=35516 65&prodNameId=3544441&swEnvOID=4036&swLang=13&mod e =2&taskId=135&swItem=hh-63897-1
- Execute the install. Notice that after installing, it will run the update utility.
Cancel it
- Go to the folder that the installer left the files, in my computer it was C:\iPAQ\SP40181, then you will notice that the file FLASH.NBF is there
- From the necessary software download, look for XVI32 and execute it, then open the file FLASH.NBF
- Click on the menu "XVIscript" then "Editor"
- In Editor, type: DEL 3432 then click on the "Execute" button
- It will ask you to save the script, it's not necessary
- Then Save the file as Flash.DIO.

4- Transfering the file FLASH.DIO to the iPaq
- Now that you have your Flash.DIO, either using my file, or the one you edited, you need to transfer it.
- From the necessary software package, go to DNW, open DNW.exe, [Configuration] => [Option], change [Download Address] from 0xc000000 to 0x3000000. You can keep the application open.
- Rename FLASH.DIO to FLASH.nb0
- Bring your Device to "Download image" mode. To do this, press the OK + VOLUME DOWN + Reset
NOTE: Please notice OK buton is the one below the track wheel, on the right side, not the one in the QWERTY keyboard.
- Plug your device to PC. I used Windows Vista drivers and I did not need to use other drivers. In case the drivers are needed for you, then manually select driver to install (files are in SEC folder, on DNW)
- Back to DNW application, click on menu on [USB Port] => [UBOOT] => [UBOOT] and select Flash.nb0. After this, you should start seeing a progress bar, indicating that the file is being transfered.

After the transfer is complete, the screen will display # signs for the progress while the firmware is installed. It takes a while. After it's finished, the iPaq will reboot and do a Clean Boot by itself. It takes a while again. After it's finished, it will start to boot and you will see the green Windows Mobile 6.1 boot screen.
viki je odsutan trenutno   Reply With Quote
Staro 20-12-2010   #10
dxdy
Super Moderator
 
dxdy's Avatar
 
Dob: 47
Mobitel: Xiaomi Poco X3 NFC
Operater: ViP
Postovi: 7,634
Zahvalio: 428
Pohvaljen 6,964 Puta u 2,902 Posta
Uobičajeno

meni je jasan ovaj dio oko hex editora ali dalje ne kuzim od "From the necessary software package, go to DNW, open DNW.exe, [Configuration] => [Option], change [Download Address] from 0xc000000 to 0x3000000. You can keep the application open."

skines http://www.handshake.de/user/chmaas/.../xvi32_231.zip

pokrenes i otvoris fajlu FLASH.NBF, odes na XVIscript, Editor pa upises DEL 3432 i kliknes na Execute. kad zatvoris ne moras snimati skriptu vec snimis Flash.DIO sa File - Save As

Zadnji uredio dxdy ; 20-12-2010 u 19:35.
dxdy je odsutan trenutno   Reply With Quote
Zahvalili:
viki (21-12-2010)
Staro 21-12-2010   #11
viki
Forumaš
 
Mobitel: HP iPAQ 914c
Operater: VIP
Postovi: 21
Zahvalio: 6
Pohvaljen 0 Puta u 0 Posta
Uobičajeno

Dxdy,

hvala probao sam sve i ovo sam skinuo sa sljedećeg linka :
http://forum.xda-developers.com/showthread.php?t=459123

Probao sam sve, laptop mi prepozna device pomoću navedenog softwera, mđutim mobitel stoji u statusu "dovnload image", a na lptopu ne vidim progres da se vrši prijenos podataka. Mobitel i dalje pokreće sve do "GP loga". Dođe mi da bacim mobitel. Katastrofa!!!
viki je odsutan trenutno   Reply With Quote
Odgovori

Alati Za temu

Dozvole Podforuma/Teme
Ne možete otvarati nove teme
Ne možete odgovarati na postove
Ne možete slati privitke
Ne možeteuređivati vlastite postove

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


           

Vremenska Zona je GMT +2. Trenutno je 03:51 sati.


Powered by vBulletin ©
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.3.2